21-3691Erev1.3
HSC-IP Module Installation Instructions
9 / 2008
© 2008 CSG Security Inc. / Sécurité CSG Inc. Page 7 of 13
Guardall (formerly VEREX Technology)
5201 Explorer Drive, Mississauga, Ont., Canada. L4W-4H1
sales@verextech.com +1 905.206.8434 | support@verextech.com +1 905.206.8436 | Fax: +1 905.629.4970
www.guardall.com | +1 877.249.9993
Using the Discovery Feature
NOTE: The following Discovery feature can be used over a Network or by the Direct Connection detailed in the following
Figure 1 diagram.
Previous Version 3 IP Module Discovery Feature Procedure
1. Ensure the 12VDC power is OFF to the IP module.
2. Press and hold the Discovery button on the IP module.
3. While still pressing in the Discovery button, put the 12VDC
power ON to the IP module.
4. The 3 green Communication lights on the IP module will flash
on and off together. This means that the IP module is in the
Discovery Feature. Stop pressing the Discovery Feature
button.
Version 4 HSC-IP Module Discovery Feature Procedure
1. Like the version 3 IP Module, the version 4 HSC-IP Module can be put in the
Discovery Feature the same way by de- and re-powering. HOWEVER, the 3
green Communication lights must be watched very closely and the moment they
begin flashing, the Discovery Feature button must be released.
2. While the Version 4 HSC-IP Module is powered, the Discovery Feature button
can be pressed and held to put the HSC-IP Module into the Discovery Feature.
HOWEVER, the 3 green lights must be watched very closely and the moment
they begin flashing, the Discovery Feature button must be released.
Green Host RX
RJ45
Female
Network
Connector
Cross Over Cable from
PC Network Card
Network LEDS
Green
On = network
connection OK.
Flashing
= network
activity
1
2
3
Yellow Host TX
Yellow SIP TX
Green SIP RX
Yellow Aux TX
Green Aux RX
Communication LEDS
Not Used
Discovery Mode
Program Button
Wire
Connectors
(+) 12VDC
Orange
Yellow RS485 B
Blue
Green RS485 A
Red
Black
( ) Neg. GND
Not Used
HSC-IP
Module
Yellow
Jumper
Pins
Jumper
Pins
Not Used
Not Used
312 12
TB4
TB5
Host A
0V
Host B
Auxiliary (+)12VDC
0V
HSC-IP
PC Utility
Security System Main
Controller HSC-IP
Module Connections
xL/AFx
312
TB16
MONITOR ISM/AFx
312
TB2
4
(+)
(
–)
Aux
12VDC
(+)
(
–)
Host A
Host B
0V
Communication LEDS
Green Host On indicates communication
between the security system IP module and the
main control board.
Green SIP
Flashing indicates valid IP address.
Yellow SIP
On means communicating with HSC-IP
Receiver. Rapid flashing means communication with
backup receiver.
SIP (Security Internet Protocol)
Green and Yellow AUX
Indicate Director Software
communication.
Green
Yellow
Red
Black
Figure 1
Discovery Mode Lights
The 3 Green Communication Lights will flash on and
off together when the HSC-IP Module is in the
Discovery Feature.
• After getting the 3 green Communication lights to flash at the same time on the HSC-IP Module for the Discovery Feature,
press the “Connect” button at the top right of the Utility screen.
If the connection was successful, these top row buttons will be enabled:
• Disconnect Close communications with the HSC-IP module.
• Get From Obtain existing settings in an HSC-IP module.
• Send To Transfer settings made in the Utility to the HSC-IP module.
(62 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern