Verex Monitor ISM Spezifikationen PDF herunterladen (Seite 11)

22-9058 v2.1

Welcome

PCPanel IP

Cent. Mon. with IP

Ref. Topics

2.2 Component Wiring for

PCPanel with IP

2.2.1 Wiring Concept (PCPanel with IP)

LAN/WAN

ISM/AFx

Main

Panel

Director Software

10BaseT / RJ45

Up to 30 panels

per connection

Panels

Pwr Req'd

12V, 250mA

To sensors,

modules,

etc.

Interface

Module

)

Single-panel connections needed for

panel-initiated comms (details in 2.1.1).

To sensors,

modules, etc.

(single PC, or client/server)

RS485 (24AWG, 4-wires,

shielded) Tested to 300m/1000ft

(Optional)

(

Shared with SIP

reporting, if applicable.

(wiring is separate)

2-wire power cable

required if power

supply is separate.

∗

Never use reader

cable for this!

Use 24 AWG, 4 conductor comms cable FT4 P/N 120-3401, FT6 P/N 120-3405. Add a 2

cable of the same

type for cable runs over 4 wires. Use 18AWG power cable FT4 P/N 120-3400, FT6 P/N 120-3404 for power

supply connections.

2.2.2 Wiring Details (PCPanel with IP)

TB2

Main Panel

Motherboard

TB2

TB16

+12 v

Locations

Yellow wire

Green wire

∗

Shared w/ SIP reporting (if applicable)

Main Panel

Module Bus

(assoc. with

any ext. P/S)

1234

298-8522

(3A)

TB10 - TB13

'B'

Connector

IP Interface Module

RJ45

To Network

+12V

Data A

Data B

Other wires/connectors: used

ONLY with SIP reporting (for

SIP wiring, see section 3.3)

∗

If separate P/S used instead, IP board TB2-3 (Dir Ground) must be

shorted to related motherboard TB16-3 (0V).

See Sect. 4.2, Figure 5.

If P/S is interfaced with Module Bus remotely to help power

other devices (+12V connection), install isolating diodes (3

A; P/N: 298-8522) at the panel (Module Bus +12, with band

facing away from panel connection).

Power Considerations

During Configuration: 12V power and a LAN (not WAN)

connection is required when configuring the IP Module.

(Use RS-485, shielded

cable if IP board is

remotely located.)

A485

B485

TB16

To TB16 on

2nd panel

(RS-485, shielded)

TB16

IP Module

Main Panel

Motherboard

TB2

Control Box Mounting IP Module

board wires are made purposely long to

allow running them around main panel

motherboard to avoid electrical

interference across the motherboard.

Prewired terminal blocks

for connections on

motherboard are

supplied.

(+)

(-)

Battery Terminals

this end.

Black wire

Red wire

TB2

A485

B485

(if applicable)

132

To TB16 on

next panel etc.

First Panel

For more detail on power and grounding requirements, refer to sections 1.4 and 1.5.

LED Reference: For details on the

operation of the on-board LED’s, refer to

the hardware reference, Sect. 4.2.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 51 52

Kommentare zu diesen Handbüchern

Keine Kommentare

Verex Monitor ISM Spezifikationen Seite 11

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Verex Monitor ISM